Bostech # MP3049 Fuel Injector
Info and Price - Bostech # MP3049 |
Actual appearance may vary
|
The Bostech MP3049 Fuel Injector has been stripped and cleaned. All O-Rings, Pintels, etc. are replaced. The fuel flow on all of our injectors is rigorously tested prior to our factory certification.
Each Bostech Fuel Injector includes both the Injector and the Seal Kit. Click Here for Installation Instructions.
Bostech factory certifications meet or exceed industry standards for fuel flow, and come with a 2-Year, 24,000 Mile Warranty. Read below to find CVU Part # 32-11151 specifications; including what vehicles the Bostech MP3049 fuel injector is made for, all part numbers, and information on how to install the Bostech MP3049 gasoline fuel injector.
Questions? Call 1-877-273-0021
|
List Price:
Our Price:
You Save:
Core Fee: |
$82.00
$34.95
$47.05
$10.00 |
|
|
|
SPECIFICATIONS
|
1993 Buick Century 2.2L
1994 Buick Century 2.2L
1995 Buick Century 2.2L
1996 Buick Century 2.2L
1992 Chevrolet Beretta 2.2L
1993 Chevrolet Beretta 2.2L
1994 Chevrolet Beretta 2.2L
1995 Chevrolet Beretta 2.2L
1996 Chevrolet Beretta 2.2L
1992 Chevrolet Cavalier 2.2L
1993 Chevrolet Cavalier 2.2L
1994 Chevrolet Cavalier 2.2L
1995 Chevrolet Cavalier 2.2L
1996 Chevrolet Cavalier 2.2L
1997 Chevrolet Cavalier 2.2L
1992 Chevrolet Corsica 2.2L
1993 Chevrolet Corsica 2.2L
1994 Chevrolet Corsica 2.2L
1995 Chevrolet Corsica 2.2L
1996 Chevrolet Corsica 2.2L
1994 Chevrolet LLV 2.2L
1995 Chevrolet LLV 2.2L
1994 Chevrolet S10 Truck/Blazer 2.2L
1995 Chevrolet S10 Truck/Blazer 2.2L
1996 Chevrolet S10 Truck/Blazer 2.2L
1997 Chevrolet S10 Truck/Blazer 2.2L
1993 Oldsmobile Cutlass 2.2L
1994 Oldsmobile Cutlass 2.2L
1995 Oldsmobile Cutlass 2.2L
1996 Oldsmobile Cutlass 2.2L
1993 Oldsmobile Cutlass Ciera 2.2L
1994 Oldsmobile Cutlass Ciera 2.2L
1995 Oldsmobile Cutlass Ciera 2.2L
1996 Oldsmobile Cutlass Ciera 2.2L
1995 Pontiac Sunfire 2.2L
1996 Pontiac Sunfire 2.2L
1997 Pontiac Sunfire 2.2L |
OEM # 17113197, 17113124, 17112693, 25169153, 8171131970, 17100435, 5030435, 17109130
Bostech Part # MP3049
CVU Part # 32-11151 |
Call 1-877-273-0021 for
more parts that match this vehicle! |
Installing remanufactured fuel injectors is a fairly simple process and can be done yourself with a few basic tools and a little time. If you are not familiar with your fuel injector system, grab your vehicle's repair manual to assist along the way.
-
Remove the air box, unless you have already upgraded your air intake system, then this step is not necessary. If you will be installing a supercharger with it, remove the air inlet temperature sensor as well. They tend to stick a little, so be patient with it.
-
Take out the bolts holding the strut tower brace on and remove it. These bolts are generally 10 mm in size and there will be eight or so of them. A standard 10 mm torque wrench should do the trick. If they stick, use a little engine cleaner to help loosen them.
-
Continue removing components until you reach the fuel rail. These components will include: idle air control valve, EGR, throttle position sensor, throttle cable, EGR valve, intake manifold, all hoses, electrical connectors, fuel lines and, alas, the fuel rail which houses the fuel injectors.
-
Wiggle the fuel injectors off much like when replacing spark plugs and wires. Each one will spray some gas, so no smoking during this process. Place the new injector in place of the old on and lubricate the O-ring with some 20W engine oil. Reinstall everything and you are done.
If you're getting raw fuel to exhaust pipe:
-
Check for open intake valves.
-
(Bad pressure regulator) It builds too much pressure in the fuel rails and consumes a large amount of excess gasoline. Also, ½ gallon of fuel ends up in the oil pan. In this case, the oil should be changed immediately.
If you're getting raw fuel to exhaust pipe
on early Vortec 4.3L engines:
-
Plastic fuel lines that connect the injector’s fuel housing to the metal fuel supply should be replaced with the injector assembly to prevent engine flooding, oil contamination, and engine stall. Reference GM CPI nut kit, Bostech Part Number 55163.
-
Fuel in the exhaust pipe could be a symptom of a leak in the fuel pressure regulator.
-
Poppits on spray nozzle could be stuck open if the area they connect to is not clean and debris contaminates the spray tips.
To find the fuel leak:
-
Remove upper intake manifold
-
Turn the key on (but do not attempt to start the vehicle)
-
After the fuel pump comes on, you should be able to visually identify any leaks.
|
|
|
|
|
 |
|
|
