Bostech # MP4164 Fuel Injector
Info and Price - Bostech # MP4164 |
Actual appearance may vary
|
The Bostech MP4164 Fuel Injector has been stripped and cleaned. All O-Rings, Pintels, etc. are replaced. The fuel flow on all of our injectors is rigorously tested prior to our factory certification.
Each Bostech Fuel Injector includes both the Injector and the Seal Kit. Click Here for Installation Instructions.
Bostech factory certifications meet or exceed industry standards for fuel flow, and come with a 2-Year, 24,000 Mile Warranty. Read below to find CVU Part # 42-12126 specifications; including what vehicles the Bostech MP4164 fuel injector is made for, all part numbers, and information on how to install the Bostech MP4164 gasoline fuel injector.
Questions? Call 1-877-273-0021
|
List Price:
Our Price:
You Save:
Core Fee: |
$82.00
$34.95
$47.05
$5.00 |
|
|
|
SPECIFICATIONS
|
1998 Acura SLX 3.5L
1999 Acura SLX 3.5L
1998 Honda Passport EX 3.2L
1999 Honda Passport EX 3.2L
2000 Honda Passport EX 3.2L
2001 Honda Passport EX 3.2L
2002 Honda Passport EX 3.2L
1998 Honda Passport LX 3.2L
1999 Honda Passport LX 3.2L
2000 Honda Passport LX 3.2L
2001 Honda Passport LX 3.2L
2002 Honda Passport LX 3.2L
1998 Isuzu Amigo 3.2L
1999 Isuzu Amigo 3.2L
2000 Isuzu Amigo 3.2L
2002 Isuzu Axiom 3.5L
2003 Isuzu Axiom 3.5L
1998 Isuzu Rodeo 3.2L
1999 Isuzu Rodeo 3.2L
2000 Isuzu Rodeo 3.2L
2001 Isuzu Rodeo 3.2L
2002 Isuzu Rodeo 3.2L
2003 Isuzu Rodeo 3.2L
2004 Isuzu Rodeo 3.2L
1998 Isuzu Trooper 3.5L
1999 Isuzu Trooper 3.5L
2000 Isuzu Trooper 3.5L
2001 Isuzu Trooper 3.5L
2002 Isuzu Trooper 3.5L
1999 Isuzu Vehicross 3.5L
2000 Isuzu Vehicross 3.5L
2001 Isuzu Vehicross 3.5L |
OEM # 8171202710
Bostech Part # MP4164
CVU Part # 42-12126 |
Call 1-877-273-0021 for
more parts that match this vehicle! |
Installing remanufactured fuel injectors is a fairly simple process and can be done yourself with a few basic tools and a little time. If you are not familiar with your fuel injector system, grab your vehicle's repair manual to assist along the way.
-
Remove the air box, unless you have already upgraded your air intake system, then this step is not necessary. If you will be installing a supercharger with it, remove the air inlet temperature sensor as well. They tend to stick a little, so be patient with it.
-
Take out the bolts holding the strut tower brace on and remove it. These bolts are generally 10 mm in size and there will be eight or so of them. A standard 10 mm torque wrench should do the trick. If they stick, use a little engine cleaner to help loosen them.
-
Continue removing components until you reach the fuel rail. These components will include: idle air control valve, EGR, throttle position sensor, throttle cable, EGR valve, intake manifold, all hoses, electrical connectors, fuel lines and, alas, the fuel rail which houses the fuel injectors.
-
Wiggle the fuel injectors off much like when replacing spark plugs and wires. Each one will spray some gas, so no smoking during this process. Place the new injector in place of the old on and lubricate the O-ring with some 20W engine oil. Reinstall everything and you are done.
If you're getting raw fuel to exhaust pipe:
-
Check for open intake valves.
-
(Bad pressure regulator) It builds too much pressure in the fuel rails and consumes a large amount of excess gasoline. Also, ½ gallon of fuel ends up in the oil pan. In this case, the oil should be changed immediately.
To find the fuel leak:
-
Remove upper intake manifold
-
Turn the key on (but do not attempt to start the vehicle)
-
After the fuel pump comes on, you should be able to visually identify any leaks.
|
|
|
|
|
 |
|
|
